- Contact Person : Ms. Su Selena
- Company Name : Shenzhen Duoweier Technology Co., Ltd.
- Tel : 86-755-27913140
- Fax : 86-755-27911880
- Address : Guangdong,Shenzhen,Floor 7,Tower B, Junyi Industrial Park,47 zone of Baoan District,Shenzhen,China
- Country/Region : China
- Zip : 518000
DVL-106C UHF RFID reader
DVL-106C UHF RFID reader
main function Introduction of UHF RFID reader
(1) Orientation Identificationof UHF RFID reader
The DVL-106C UHF RFID reader adopts the infrared and radio frequency synchronous communication technology. Only in the infrared scanning scope can the 60 degree infrared signal exchange with the internal code (card number). At present, this technology is the only one that can solve the strict direction orientation.
(2)Adjustment of the reading distance of UHF RFID reader
The DVL-106C UHF RFID Reader can stably identify 15 meters and the signal can penetrate into the cars’ anti-explosion metal film. In order to achieve 3-15 meters identification, the DVL-106C UHF RFID reader can be adjusted according to the actual needs when installed.
(3)Dormancy to Save Electricity of UHF RFID reader
The electronic card of DVL-106C UHF RFID reader used with the RFID adopts the latest dormant activation. There is no energy consumption when the RFID tag is standby. When the RFID tag enters the infrared scanning area of our UHF RFID reader, the RFID tag will be activated and turn on the power automatically to send the internal code (card number) to our UHF RFID reader. When the RFID tag leaves the area, our RFID tag will turn off the power and become dormancy. Therefore, it greatly extends the card’s battery life.
(4) Zero-interference of UHF RFID reader(Machine Code Validation Technology)
Every DVL-106C UHF RFID reader has its own machine code. It sends out 60 degree infrared signal and its machine code simultaneously. After waken up by the infrared scanning signal, the RFID tag will send its number and the machine code. When the UHF RFID reader receives the RFID tag number and the machine code, it will check the number firstly. If the RFID tag number matches with the UHF RFID reader, the UHF RFID reader is effective and if not, it will be deleted automatically. UHF RFID reader needs to set up different machine codes while many RFID readers are used at the same time in order to solve the interference of cars in the vicinage lanes or the following cars and many other issues.
(5) Reading Styles of UHF RFID reader
UHF RFID reader has two kinds of reading styles: Reading by loop detector and automatic reading. The factory default of our UHF RFID reader is the latter one (automatic card reader). If you want to change it, please refer to the introduction of UHF rfid reader
(6)Uploading Tag Number Alternately of UHF RFID reader
The UHF RFID reader can read tags’ number continually. The time interval of UHF rfid reader can be set up freely so as to prevent uploading too fast to cause death to the system controller. The factory’s default of UHF rfid reader is two seconds at one time.
(7)Working Mode of UHF RFID reader
UHF RFID reader has automatic mode and manual mode. The automatic mode of UHF rfid reader applies to the open-air car parking management system. In the underground car parking lot, please set the UHF rfid reader to the manual mode and adjust the signal’s strength until the UHF RFID reader can read directionally, because infrared signal may be reflected in the closed space which can cause non-directional card reading.
(8) Automatic adjustment of the signal’s strength of UHF RFID reader
The UHF RFID reader uses environmental sensor technology. In the automatic mode signal the UHF RFID reader can be adjusted automatically according to the changes of environment so as to ensure the UHF RFID reader works in the most stable state
(9)Multiple Interface Output of UHF RFID reader
This UHF RFID reader has four kinds of interface output: Wiegand26,Wiegand34,Active 485,Passive485,which can be set according to the requirements.
(10) Self-detection of the signal interference of UHF RFID reader
This UHF RFID reader can detect the signal interference automatically. When UHF RFID reader detects the same radio frequency, the high frequency of power or other interference, the blue LED of rfid reader will blink. It needs people to eliminate the sources of interference if they affect the communication between the UHF RFID reader and the RFID tag.
DVL-106C UHF RFID reader
